MegaLite Axis Bedienungsanleitung PDF herunterladen (Seite 8)

Preliminary work

1. Prepare base grade exceeding the

planned terrace surface by 50 cm on all

sides with a sloping of 4 % and install

drainage in the ground.

2. Make a stable gravel or ballast bed

(frost-safe) with 2 % sloping. Then cover with

fine gravel to level uneven spots.

Sub-structure

3. To begin, click the FIX STEP mounts

at the same height level into all FIX STEP

plates. Then stick a piece of retaining band

onto the centre of each one.

Optional: To increase the structure and to

improve step dampening, click a FIX STEP

comfort pad with the corresponding at-

tachment into the mounts. Then stick a pie-

ce of retaining band onto the centre of the

attachments.

→ Cf. page 13

4. Place the FIX STEP edge plates DUO

at a distance of 4 cm parallel to upright

components and at an axis distance of max.

65 cm. Distribute FIX STEP plates parallel

to these at an axis distance of 50 cm. At the

end of the terrace, place FIX STEP edge

plates DUO again.

→ Cf. floor plan substructure

5. To minimize protruding of the construc-

tion planks, turn the FIX STEP plates.

6. For a terrace length of more than

360 cm, a FIX STEP edge plate must be

placed in the area of the end joint of the

smooth-edged boards.

Max. 50 cm Max. 50 cm

1cm

32 cm

7. Click construction plank (40 × 60 mm)

into the FIX STEP mounts with the grooves

down.

8. For a terrace width of more than

360 cm, the ends of the construction plank

must always be offset to each other. To do

so, connect the ends of the planks with a

FIX STEP connection clip adjusted to

32 cm and screw on to one side. Maintain a

distance of 1 cm between the construction

planks.

→ Cf. floor plan substructure 8

32 cm

15,5 cm1cm

7cm

4x35

9. For free expansion, the ends of the

smooth-edged boards and of the construc-

tion planks must be positioned in the same

place.

1cm

6cm6cm

32 cm

In addition, to ensure free expansion the

FIX STEP connection clip must be left open

2 cm wide and 1 cm deep for subsequent

installation of the smooth-edged board in

the area of the screw connection.

13 cm

2cm2cm

10. Then exactly align all construction

planks on the side where installation of the

boards begins.

11. After installing the construction planks,

check the position of the FIX STEP plates

and adjust them if necessary.

12. Place perforated tape below the

construction planks and screw it onto all

construction planks by means of the FIX

STEP connection clip. The perforated tape

is used for bracing the terrace.

→ Cf. 12

III

x16

4x35

13. To attach the FIX STEP edge clamps,

cut out the construction planks first only on

the side from where the boards are to be

installed, 12 cm away from the edge, 5 mm

deep and 2 mm deep.

→ Cf. 13

After that, the two-part FIX STEP edge

clamp is fitted into this groove and to the

construction plank by means of pliers.

5 mm

12 mm

III

14. To prevent subsequent slipping of the

boards, self-adhesive retaining tape must

always be fastened to the construction

plank that is closed to the centre of the

boards.

→ Cf. 14

Installation of the boards

15. The first board is pressed into the

positioned edge clamps. Keep a distance of

2 cm to upright, fixed components. When

using the optional house connection

profile, first insert the board, then position

it.

→ Cf. 15

16. The connected FIX STEP connection

clips are then set onto the each of the

construction planks, pushed against the

board and engaged by means of pliers.

I II

III

17. If boards are to be fastened at a

distance of about 10mm to the ends of

the construction planks, it is necessary to

insert groove bridges before the connec-

tion clips are mounted.

18. For open decks, cover caps must be

clipped onto edge and connection clips.

19. After installation of three rows of

boards, the deck should be measured so

that parallel installation is ensured.

Attention: Since the FIX STEP connection

clips are only used to secure the boards in

vertical position, they must be fixed to the

construction planks in every third row of

boards by means of the supplied screws

before they are clipped on. Repeat procedure

until the last but one board is installed.

20. Then determine the length of the con-

struction planks and saw them off to be

flush.

21. Then create the groove for the edge

clamp and finish installing the boards.

→ Cf. installation step 13

22. Now cut the front end of the boards in

the area of the edge to length with boards

extending 1.5 cm over the construction

planks and bevel the cutting edge.

23. Cut smooth-edged boards to length

parallel to the construction planks; the

smooth-edged board on both ends of the

terrace must be 1.2 cm shorter than the

construction plank.

6cm

1,2cm

Hold on smooth-edged board and drill

together with the construction plank using

∅ 7 mm drill holes. Keep the maximum

distance of 6 cm to the ends and 50 cm

between drill holes. Then re-drill smooth-

edged boards with ∅ 10 mm, lower and

attach by means of screw, washer and nut

using a distancing groove of 1 cm to adjust

to the terrace deck.

1cm

1,5cm

4cm

M8x80

Cut smooth-edged boards

parallel to the substructure and drill

together with the construction plank

with ∅ 7 mm. Re-drill smooth-edged

boards with ∅ 10 mm and install them.

M8x80

4cm

1cm

clippe

19.

board

that p

Atten

clips a

vertic

const

before

until t

20.

struc

flush.

21.

clamp

→ Cf.

22.

the ar

exten

plank

OFFENES DECK

4 %

2 %

Sloping in

installation direction

MOUNTED INSTALLATION

10,4 cm

Max. 65 cm

Max. 50 cm

Keep the minimum distance of

4 cm to upright, ﬁ xed components.

Ventilation

from below

Water draining

for drainage system

Hint:

The FIX STEP system does not create

the sloping of the terrace.

Hint:

WAVE barefoot boards (open) require

increased care and cleaning eﬀ orts – it is

necessary to remove dirt from the grooves

in the boards regularly. The distance

between the axes of the construction

planks is 40 cm. A minimum sloping of

2% in longitudinal direction is absolutely

necessary.

4 cm

distance from edge

plate DUO to ﬁ xed

components

Max. 50 cm

distance between

the axes of all

plates in installation

direction of the

boards

Distance between axes

of all plates in installation

direction

Max. 65 cm

Set connection clip crosswise in the

centre between plates

FIX STEP SYSTEM

OPEN DECK

2 cm

GROUND LEVEL INSTALLATION

Hint: Ground level installation

To ensure the required ventilation from

below, ground level installation is only

permitted as open deck. A distance

of 2 cm to upright, ﬁ xed components

must always be kept.

Floor plan substructure

4 cm

Attention:

Since the FIX STEP connection clips are only

used to secure the boards in vertical position,

they must be fixed to the construction planks

in every third row of boards by means of the

supplied screws before they are clipped on.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 16 17

Kommentare zu diesen Handbüchern

Keine Kommentare

MegaLite Axis Bedienungsanleitung Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Flutlichter MegaLite Axis